Home Docs Tuning & AutoTune

ThunderMax Decel Pop Tuning

Updated on Nov 13, 2026

Deceleration pop depends on the engine, exhaust and rider preference. Use the following procedure to develop deceleration and transition fueling before deciding whether Decel Cut is needed.

View / Download the Decel Pop Tuning Guide — PDF

Why deceleration pop occurs

Open or loud exhaust systems make deceleration pops more noticeable. Air drawn into the exhaust during closed throttle can ignite unburned fuel. The two approaches are to cut fuel during deceleration or to keep the engine running so the fuel burns in the engine. Each has tradeoffs, and the final choice depends on the engine/exhaust combination and rider preference.

Some combinations can eliminate popping without Decel Cut. Others can only minimize it. Most combinations improve over time as AutoTune learns; enable Decel Cut only if the remaining exhaust pop or talk is unacceptable.

OEM deceleration-cut example

In this OEM example, fuel is turned off during closed-throttle deceleration after RPM has exceeded about 2300, then restores fuel below about 1796 RPM. Accelerating only to 2100 RPM may leave the engine burbling down toward 1280 RPM; accelerating to 2500 RPM can activate fuel cut and produce a flat engine-braking sound. When fuel returns near 1796 RPM, the engine may fire softly or produce a slight forward bump.

ThunderMax adjustment

ThunderMax allows the feature to be enabled or disabled and its RPM levels to be set. Decel Cut does not correct inaccurate transition fueling when the throttle is reopened and can cause shift pops. Tune the deceleration and transition areas first. Stock exhausts can also pop, although the sound is less noticeable.

Required: Keep the Decel Cut feature OFF throughout the tuning process in Steps 1–3.

Step 1: Repeat closed-throttle decelerations

In a higher gear (3rd or 4th) so RPM falls slowly, accelerate to 2500 RPM. Close the throttle completely and decelerate to 1500 RPM. Repeat five or more times.

Step 2: Repeat just off closed throttle

Accelerate to 2500 RPM again. Feather the throttle just open from its closed position so the system can see and adjust that condition. Repeat several times. Continue using slow feathering from closed to just open, and occasionally a little farther. Slow, consistent changes stabilize transition fueling and give AutoTune time to adjust areas not developed quickly in normal riding.

Step 3: Restart and continue across the RPM ranges

Before repeating the process, stop, turn the engine off and restart. This signals AutoTune to increase adjustments when needed. Use the RPM ranges below as a guideline. Spend more time in troublesome areas and less where the popping becomes quieter.

Start RPM Decelerate to RPM
2500 1500
2750 2250
3000 2500
3250 2750
3500 3000
4000 3500
4500 4000
5000 4500

Step 4: Enable Decel Cut if needed

If popping remains unacceptable after tuning, enable Decel Cut (1). Adjust its variables for the engine, exhaust and rider preference. Two common setting pairs are:

  • Broad deceleration control: RPM Low 1792, RPM High 2304.
  • High-RPM popping only: RPM Low 2944, RPM High 3200.

Step 5: Adjust post-fuel enrichment

If a forward bump occurs when RPM falls to RPM Low and fuel returns, reduce Decel Post Fuel Enrichment. If no bump is felt, or a crackle occurs while advancing the throttle during deceleration, increasing the value may help.

Base maps are preset to reduce deceleration pop, but exhaust combinations and rider preferences vary. Proper tuning can also improve response as the throttle is reapplied.

Need help?

Contact ThunderMax technical support or email support@thunder-max.com with your questions.

Based on the ThunderMax “Decel Pop Tuning” technical document, version 0.5, dated November 11, 2026.